Artikkeli numero 512147

fischer Zykon panel anchor FZP II 11 x 21 M6/VS/4 AL

Huippu ominaisuudet

Stand-off installation and compensation of panel thickness tolerances for highest visual requirements.
The integrated suspension nut combined with the suspension clasps Vertical Solution enable an easy panel installation (keyhole principle)
For all natural stones class I-IV.
Stress-free fixing enables high loads and use of thin panels.
Sleeve made of stainless steel.

The suspension anchor with the fischer Vertical Solution for natural stone façade panels.

Edut

The adapted shape of the undercut anchor ensures a positive-locking attachment free from expansion pressure in a conical undercut drill hole.
The fixing of the undercut anchor is not visible on the exposed side, creating a visually attractive and consistent façade surface.
Setting the anchor using undercut technology allows the user to always select the optimal structural position in the façade panel. This greatly reduces panel deflection.
The anchor allows for higher pull-out loads, compared to commonly available systems.
Using a constant remaining wall thickness as a reference value when drilling holes allows users to compensate panel thickness tolerances.

The concealed stand-off installation solution using undercut anchors for heavy natural stone façade panels. This anchor can only be used with the fischer Vertical Solution subframe system. Suspension brackets designed based on a lock and key principle are used to install the undercut anchors. This technology defines a constant distance between the front of the panel to the connection face on the FZP II anchor (RWT = remaining wall thickness) as a reference dimension for drilling. This technology can be used to compensate panel thicknesses and create a flat façade surface by stand-off installation anchors.

Toimintaperiaate / asennus

Wet diamond drilling - first cylindrical to a constant reference dimension for the remaining wall thickness (RWT), then conical to create an undercut drill hole.
When the undercut anchor is installed, an optimal positive-locking connection is created between the expanding part and the drill hole.
The anchor is installed in the conical undercut drill hole using stand-off installation.
The ability to compensate panel thickness tolerances helps create a flat façade surface.
Suspension brackets designed based on a lock and key principle are also used during installation.

Mounting Strip 1 Picture

1 / 6

ETA Certification Document

pdf, ETA-11/0145

European Technical Assessment for fischer-Zykon-panel anchor FZP II - Fastener for the rear fixing of facade panels made of selected natural stones according to EN 1469

Luotu 09.06.2022

DOP - Declaration of Performance

pdf, DoP No. 0307

Declaration of Performance for fischer Zykon-panel anchor FZP II

Luotu 01.07.2022

DOP - Declaration of Performance

pdf, DoP No. 0261

Declaration of Performance for fischer Zykon-panel anchor FZP II

Luotu 11.01.2021

ETA Certification Document

pdf, ETA-22/0400

European Technical Assessment for fischer ZYKON FZP II for fixing Mirage facade panels

Luotu 25.08.2022

DOP - Declaration of Performance

pdf, DoP No. 0322

Declaration of Performance for fischer Zykon-panel anchor FZP II (for Mirage)

Luotu 12.10.2022

Lisätarvikkeet

ETA-hyväksyntä
Kiinnityssyvyys ( h_ef )	12 - 16 mm
Levyn min. paksuus	20 mm
Tyyppi	Abstandsanker
Kokonaispituus ( l )	21 mm
Projection length	4,5 mm
Kierre ( M )	M6
Cylindrical diameter	11 mm
Undercutdiameter	13,5 mm
Materiaali	A4
Kuorimateriaali	A4
Määrä	250 Pa.
GTIN (EAN-Code)	4048962112580

fischer Zykon panel anchor FZP II 11 x 21 M6/VS/4 AL

Edut / tuotekuvaus

Käyttö ja hyväksyntä

Kokoamisohje

Tekniset tiedot

Ladattavat asiakirjat